How To Reset H20 Light On Whirlpool Refrigerator (2024)

Contents

If you have a Whirlpool refrigerator, you may notice a light on the control panel that indicates the status of your water filter. This light can be green, yellow, or red, depending on the condition of your filter and when it needs to be replaced.

But what if the light stays on even after you have changed the filter? Or what if the light is red and you don’t know why? In these cases, you may need to reset the H20 light on your Whirlpool refrigerator to clear any errors and restore its normal function.

To reset the H20 light on a Whirlpool refrigerator, you need to unplug the refrigerator from its power source, locate and press the reset button, plug the refrigerator back in, and monitor the H20 light for any changes. Alternatively, you can press and hold the Ice Type and Light button on your Whirlpool fridge for as long as three seconds to reset the filter system.

Step 1: Unplug the refrigerator

The first step in resetting the H20 light on a Whirlpool refrigerator is to unplug it from its power source. This will ensure that the refrigerator is completely powered down before attempting to reset the H20 light. Locate the power cord at the back of the refrigerator and gently pull it out from the wall socket. Make sure to give it a firm tug to ensure that it is completely disconnected. It’s advisable to wear gloves during this step to protect your hands and to avoid any potential shocks.

By unplugging the refrigerator, you effectively cut off its power supply, allowing it to reset itself and clear any temporary glitches or errors. This step is crucial before proceeding with the next steps of the reset process.

How To Reset H20 Light On Whirlpool Refrigerator (1)

Step 2: Locate and press the reset button

Once the refrigerator is unplugged, the next step is to locate and press the reset button. The reset button is usually located on the control panel of your Whirlpool refrigerator, either on the front of the refrigerator door or inside the refrigerator compartment. Look for a button labeled “Reset” or with a similar indication.

Press and hold the reset button for approximately three seconds or until you hear a beep sound. This indicates that your refrigerator has been successfully reset and is ready to operate normally.

Step 3: Plug the refrigerator back in

After pressing the reset button, plug the refrigerator back into its power source and turn it on. Check if your H20 light has changed color or turned off. If not, you may need to repeat the reset process or try an alternative method.

Alternative method: Press and hold the Ice Type and Light button

If pressing the reset button does not work for your Whirlpool refrigerator model, you can try another method to reset the filter system. This method involves pressing and holding the Ice Type and Light button on your Whirlpool fridge for as long as three seconds.

The Ice Type and Light button is usually located on the control panel of your Whirlpool refrigerator, either on the front of the refrigerator door or inside the refrigerator compartment. Look for a button labeled “Ice Type” or “Light” or with a similar indication.

Press and hold this button for about three seconds or until you see the filter status change or turn off. This indicates that your filter system has been successfully reset and is ready to operate normally.

How To Reset H20 Light On Whirlpool Refrigerator (2)

FAQs

Why does my H20 light turn red?

The H20 light on your Whirlpool refrigerator turns red when your water filter needs to be replaced. The water filter helps remove contaminants and impurities from your water supply, ensuring that you have clean and fresh water for drinking and making ice. However, over time, the filter can get clogged or damaged, affecting its performance and quality.

To maintain optimal water quality and safety, you should replace your water filter every six months or sooner if you notice any signs of a faulty filter, such as:

  • Bad taste or odor in your water or ice
  • Reduced water flow or pressure
  • Cloudy or discolored water or ice
  • Particles or sediment in your water or ice

How do I change my water filter?

To change your water filter on your Whirlpool refrigerator, follow these steps:

  • Locate your water filter. It can be found either behind the kick plate, floor, or fridge ceiling.
  • Release and remove the old filter by twisting and pulling it out.
  • Attach the new filter by aligning it with the filter housing and pushing it in until it clicks into place.
  • Run at least one and a half gallons of water through the dispenser to flush out any air bubbles or debris from the new filter.
  • Reset your filter status by following one of the methods described above.

How do I know if my H20 light needs to be reset?

Some signs that your H20 light needs to be reset are:

  • It stays on even after you have changed the filter
  • It turns red for no apparent reason
  • It flashes or flickers intermittently
  • It does not respond to pressing the reset button or the Ice Type and Light button

Conclusion

Resetting the H20 light on your Whirlpool refrigerator is a simple and effective way to troubleshoot and resolve many common issues related to your water filter. By following the steps in this blog post, you can easily reset your H20 light and get it back to working properly.

We hope you found this blog post helpful and informative. If you have any questions or comments, feel free to leave them below. And don’t forget to share this post with your friends and family who own a Whirlpool refrigerator!

How To Reset H20 Light On Whirlpool Refrigerator (2024)
Top Articles
Latest Posts
Article information

Author: Twana Towne Ret

Last Updated:

Views: 5847

Rating: 4.3 / 5 (64 voted)

Reviews: 87% of readers found this page helpful

Author information

Name: Twana Towne Ret

Birthday: 1994-03-19

Address: Apt. 990 97439 Corwin Motorway, Port Eliseoburgh, NM 99144-2618

Phone: +5958753152963

Job: National Specialist

Hobby: Kayaking, Photography, Skydiving, Embroidery, Leather crafting, Orienteering, Cooking

Introduction: My name is Twana Towne Ret, I am a famous, talented, joyous, perfect, powerful, inquisitive, lovely person who loves writing and wants to share my knowledge and understanding with you.